wiki.mendiculus.info

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Distro - openwrt / ubnt edgeos ======
  * Press tab twice to get full list of commands
  * Basic command shell is busy box
  * Basic software is based off Openwrt
  * Some good options here:https://community.ubnt.com/t5/airOS-Software-Configuration/Is-there-a-Manual-on-the-Radios-command-line/td-p/402835
==== Commands: ====
Restart the device:
  reboot
To show a lot of good info aboue devicedhcp lease located in file /tmp/dhcp.leases
  info 
To see a nice breakdown of wireless do:
  iwconfig [interface]
You can pair this with ath0 to see the main one.
  iwconfig ath0
to see status of AP - more then above readout, firmware, ip, etc
  mca-status
A helpful command to see just the signal is:
  mca-status | grep signal
To see messy complex info of each station
  wstalist
You can use grep with wstalist to see some other thigns. to see connected macs:
  wstalist | grep mac 
To see all relevant data of a specific mac:
  wstalist | grep -A 36 [mac of device] 
For various options such as
  iwlist [options]
To see what access points are avaialbe (same if did peers)
  iwilist [interface] accesspoints
To see some DFS info (need to check into more)
  radarmon
To restore to factory default (for unifi it might be $syswrapper.sh restore-default, https://help.ubnt.com/hc/en-us/articles/205143490-UniFi-How-to-reset-the-UniFi-Access-Point-to-factory-defaults)
  set-default 
==== Update firmware via cli ====
Resource: https://help.ubnt.com/hc/en-us/articles/204959804-airMAX-How-do-I-upgrade-the-firmware-from-the-CLI-SSH-
  * Get firmware on device in folder /tmp/ (see below)
  * Rename file to "fwupdate.bin"
  * $fwupdate -m /tmp/fwupdate.bin
There are 3 main ways to get file to device. For First and second option you need to dl firmware onto computer
  * Windows: Use Winscp to transfer file to location. Be sure to have winscp set to scp mode, not sftp
  * Linux: $scp [user]@[dest IP] [local location file] [remote location]
SSH into device:
  * cd /tmp/
  * $wget [firmware url]
  * $mv firmware fwupdate.bin
  * $fwupdate -m /tmp/fwupdate.bin
\\ Tip: the link of file can be copied from the ubnt firmware page when you choose the fw to use.
=== Change Config File ===
Reference:https://help.ubnt.com/hc/en-us/articles/205231490-Use-static-IP-address-instead-of-DHCP-Client
\\ 
\\ When you ssh you can modify the config file by editing:
<code>
/tmp/system.cfg
</code>
You can use vi, as it is build into the ubnt devices.
Once you have saved the new config in ubiquity, you have to execute a save command and reboot. Here is a trick on how to do both:
  * $save && reboot

=== Tough switch port names ===
  * https://community.ubnt.com/t5/ToughSwitch/Tough-Switch-Port-names-and-Bridge-table-through-command-line/td-p/849116
  * cat /tmp/system.cfg | grep -i switch.port | grep -i .name

=== ubntbox ===
A propriatary tool for ubnt related things such as:
  * $ubntbox mca-status
wiki.mendiculus.info

User Tools

Site Tools

Page Tools
